(also trial machines and Equipment never used)
1 pc. roll cutting machine ACELLI (Ref. No. 5143175)
3000 mm working width, year of construction approx. 2003
dismantled and stored in heated container
1 pc. flat bed dry lamination machine SCHAETTI / KANNEGIESSER TLM 1830/1 (Ref. No. 7142920)
1830 mm working width, 3 x 400 V, 50 cycles
year of construction 2005, the machine has worked 3 months on test stand only
control voltage 230 V AC, 24 V DC
total electrical power 127,3 KW
mechanical speed drive 2-30 m/min
setting range heating = 0 - 240 C
quantity of heat = 118,8 kW
number of heat profiles = 15
number of heat cartriges = 36
length of heating zones = 1600 mm
belt width = 1880 mm
upper belt length 6400 mm
lower belt length 6700 mm
flexo pressure system
driving motor 2,2 kW
1 pc. folding and cutting machine for wet wipes WALI 130-NV (Ref. No. 5142932)
year of construction 2002
and also suitable for dry wipes
Machine for the production of nonwoven wet wipes of 400 x 380 mm, folded in 1/4, composed of circular box motion unroller, device for longitudinal folding in V, transverse bed area with exchangeable bending headstock of 400 mm, group of transverse section
by band saw with self-grinding device, counter, runout table and full electrical equipment
4 pcs. fine openers TEMAFA FOPX-Modell (Ref. No. 1121848)
1600 mm working width, year of construction 1999
single step with pin tambour and sound absorbing cabin
2 pcs. excenter dobbies type 1751 (Ref. No. 4301716)
year of construction 1999/2000
1 pc. semi automatic machine for vertical blinds TECNO SYSTEM (Ref. No. 8301205)
year of construction 1999/2000
1 pc. fixing dryer BREITENBACH (Ref. No. 7132125)
800 mm working width, year of construction 1999
gas heated
thermo fixing dryer with 70 m band content
infinitely variable band transport, controlled by 2 dancers
stainless steel construction
gas heated, max. temperature 200 C
with exit device
1 pc. tufting machine CMC OMNI-GRAPH (Ref. No. 6122101)
24 " working width, year of construction 1995 - NEVER USED
special 1/10" gauge, 240 needles, cut pile
sample Omni-Graph tufting machine
equipped with two computer controlled sliding
needle bar attachments, yarn feed (front and rear)
CMC's Advanced cutting system II and complete
with 1/2 H.P. gear motor drive, as new, never used
1 pc. foulard BOMBI (Ref. No. 7112707)
5000 mm working width, year of construction 2001 - NEVER USED
with rakel and two rollers, inclusive control
Optional: 1 pc. mixer made by BOMBI, also never used
The machine is never used and therefore in "as new" condi
1 set of shearing machines (Ref. No. 5242800)
year of construction 2000
machine 1 is type PSG-1T
machine 2 is type PSG-1T
Both machines are made in 2000
1 pc. dosage unit for chemicals and similar liquids THEN (Ref. No. 7232384)
year of construction 2001, fully automatic dosage of liquids
incl. 27 pcs. tanks for chemicals, 22 pcs. thereof with mixer
volume 640 liters each tank, 6 distribution valves, 3 control terminals
software included, good condition
2 pcs. warping machines SEGUI (Ref. No. 4172838)
year of construction 1997 + 1999 + 2000
1 Sectional Warping Machine model SW (year of construction 1999)
Equipped with beaming unit, leasing unit, warping unit
Equipped with variable speed DC motors at warping and beaming
Beam flange diameter: 1.000 mm
Safety system for beaming braking in case of off-time
Useful length 3.6 m
1 Creel COMSA for 832 cones system by trolleys.
This creel is model FKU and was constructed in 1997 and has two complete games of trolleys.
Classic spindles, tensioners, electronic stop motion devices
1 Sectional Warping Machine model SW (year of construction 2000)
Equipped wiht beaming unit, leasing unit, warping unit
Equipped with variable speed DC motors at warping and beaming
Beam flange diameter: 1.000 mm
Safety system for beaming braking in case of off-time
Useful length 3.6 m
1 Creel for 1.200 cones rotatory System. This creel was constructed in 2000
Classic spindles, tensioners, electronic stop motion devices
2 pcs. printers with inclosed ink chamber PRINTCO Ltd. K 60 (Ref. No. 7171218)
1300 mm working width, year of construction 1995, NEVER USED
with double docter system
(two printing units in one frame)
max. speed 500 m/min
as new, never used
1 pc. fiber preparation line KEITH / TRÜTZSCHLER (Ref. No. 2122129)
year of construction 2000
consisting of:
Bale Conveyor KEITH "Walking Floor"
TRÜTZSCHLER Blendomat BDT 019/2300
including
Material Funnel TRÜTZSCHLER
double magnet trap TEMAFA
deviation box TRÜTZSCHLER PWK
Electricl Control TRÜTZSCHLER
1 pc. cutter for use on quilting machines (Ref. No. 5142325)
year of construction 2000
1 pc. ring spinning machine DELPIANO (Ref. No. 3152745)
192 spindles, year of construction 2000
fully automatic, ring diameter 110 mm
1 pc. multi needle sewing machine KSL KL 970 (Ref. No. 5211131)
year of construction 1995
incl. roller table and conveyor
low number of working hours, was used for trials only
formerly used to sew thick wool material of 180 mm height
1 pc. weaving machine SULZER G6300-2200 Freiflug (Ref. No. 4112752)
2200 mm working width, year of construction 2003
16 shafts, STÄUBLI dobby 2670 made in 2003
warp thread contrl GROB 1200 / 6 lines 15 mm gauge
rails height 13 mm
8 colours
4 feeders ROI CHRONO HS
2 cloth beams, without warp beam
12 shafts GROBEXTRA ALREFIX
1 pc. nonwoven carding line with FBK NSC/THIBEAU - TRÜTZSCHLER (Ref. No. 2132130)
4500 mm working width, year of construction 2000
carding machine THIBEAU
base machine including frame, platform
reinforcing to 400 m/min, electric controls
card spare parts
carding machine doffer suction modification made in 2002
with TRÜTZSCHLER FBK 4500 Scanfeed
with profile control system VPR 539/3 and electric control panel
further details available on request
1 pc. air transporter AEROGO (Ref. No. 3302619)
year of construction 2003
dimensions leveller : 1500*900mm height : 215mm
weight unloaded : 150kg
eff. capacity : 3450kg
airconsumption : +- 2.4 Nm3/min
lifting height : 13mm
This equipment is 100% in good condition
1 pc. packing machine NORPACK AIS 400 H (Ref. No. 5192227)
year of construction 2000
bag length min. 100, max 400 mm, bag loader and conveyor
incl. welding device, (suitable for manual filling of bags)
1 pc. Nonwoven Line (Ref. No. 2112087)
3500 mm working width, year of construction NEW + never used built in 1998
The line can work into two directions for different types of products. One side produced regularly but the other production side never worked due to change in production. This part of the nonwoven line is available for sale and is consisting of:
- 1 conveyor made in PVC width 3800 mm, length 1500 mm
- 1 impregnation foulard with 2 cylinders nickel covered 445 mm diameter, 3600 mm width with a double foam distributor with variable speed
- 1 conveyor made with non adherent material width 360 mm, length 3000 mm
- 1 cylinder dryer with 10 cylinders diameter 800 mm made by WUMAG heated with steam, width 3500 mm complete with suction
- 1 curing chamber (polymerisation) width 3500 mm, capacity 27 meters, complete with heating chamber and fan
- 1 accumulator capacity 28 meters, 3.500 mm width
- 1 longit. cutting group complete with 4 cutters
working width pneumatic pressure complete with dancing for
the automat. regulation of the speed + controllable weight and meter counter, 3500 mm width
- 1 rolling unit with 2 rollers width 3500 mm + pressure cylinder
One control cabinet for brushless motors with all accessories and elements.
All machines are driven by brushless motors. Speed of the line 0-10 m/min
All machines are in conformity with CEE norms
4 pcs. air separator TRÜTZSCHLER (Ref. No. 2301919)
1200 mm working width, year of construction 1999
Second-Hand
Nonwoven Machines and used textile equipment
Summary of 2nd-hand textile machine categories:
deutsch english
francais espanol
nederlands
italiano svenska
suomi slovenski
cestina hrvatski